Independent metal stamping knowledge for global buyersB2B Network
Metal Stamping Know-HowPractical metal stamping knowledge for buyers and engineers.Write for us
Materials & Thickness

Checklist: 7 Material Properties for Deep Drawing Feasibility

Published 13 min read

Engineer checking metal sheet material for stamping
Quick answer

This checklist outlines seven key material properties engineers must verify to determine if a sheet metal part is feasible for deep drawing. It covers formability factors, testing methods, and common red flags to prevent defects like cracking and wrinkling.

Key takeaways
  • Formability is a balance between strength and ductility, measured by elongation and reduction of area.
  • Yield strength dictates press tonnage, while fracture strength determines the final drawing depth.
  • Material testing and mill certification are required to confirm that the supplied sheet meets the specified grade.
  • Texture and grain direction affect how the metal flows in the die, influencing the risk of wrinkling.
  • Always validate properties for the specific thickness and temper of the material being used.

1. Assessing Formability Limits

The core question in deep drawing is whether the material can stretch without tearing. Engineers must look beyond simple tensile strength and focus on formability factors. Ductility is the primary metric here. It measures how much the material can deform before it breaks.

A common mistake is relying only on the yield strength. A high yield strength often means a stiff material that resists deformation. However, if the elongation to fracture is low, the part will crack at the bottom of the draw. You need a material that yields easily but holds together as it stretches.

Check the elongation percentage first. For standard drawing operations, higher elongation is better. If the sheet has low elongation, you may need to reduce the drawing depth or add relief cuts. This prevents the material from exceeding its limit and tearing during the stroke.

In practice, consider a thin-walled automotive bracket made from high-strength steel. The yield strength might be sufficient for the structure, but the elongation could be too low for the required bend radius. The metal will snap at the inner radius of the bend. The engineer must then switch to a lower strength grade with higher ductility or redesign the part with a larger radius.

Another example involves stainless steel sheet. Some grades have excellent corrosion resistance but limited elongation. If you select a 304 grade with low elongation for a deep cup, the bottom will crack. A 316 grade with similar chemistry but better formability might be the correct choice. The goal is to find the balance between mechanical strength and the ability to stretch.

Always check the elongation on the material certificate. If the value is borderline, request a sample for a trial draw. A trial draw on a scrap piece reveals how the material actually behaves in the die. It shows if the material is stiff enough to hold the shape but soft enough to stretch. This step catches problems before tooling is released.

2. Evaluating Yield Strength and Tonnage

Yield strength is the stress required to start permanent deformation. This property directly ties into press tonnage and die design. A material with high yield strength requires more force to move the blank through the die.

Review the yield strength on the material certificate. This number is the baseline for your press sizing. If you select a material with a higher yield strength than necessary, you risk overloading the press or requiring a heavier die. This increases cost and setup time.

Conversely, if the yield strength is too low, the metal may not hold its shape. The part may spring back after release. You need a balance. A moderate yield strength provides enough stiffness to hold the form but allows enough flexibility to draw deep without excessive force.

Consider a deep-drawn cup made from aluminum. Aluminum has a lower yield strength than steel. It requires less press tonnage, which means you can use a smaller press. However, if the yield strength is too low, the cup will spring back after the stamp is released. The part will not hold its exact shape. You might need to add a forming step or use a die with a tighter fit to control the springback.

For steel, the yield strength is usually higher. A mild steel cup requires more force to draw. If you use a press that is underpowered, the stamp will not reach the bottom of the die. The part will be incomplete. The engineer must calculate the force required based on the yield strength and the die geometry. This calculation ensures the press has enough tonnage to complete the stroke.

The relationship between yield strength and press tonnage is not linear. As the material stretches, it hardens. This work hardening increases the yield strength during the draw. The force required increases as the draw progresses. The press must be sized to handle the maximum force, which occurs near the end of the stroke. Ignoring this increase can lead to press failure or incomplete parts.

3. Checking Fracture Strength and Limit

Fracture strength is the point where the material breaks completely. In deep drawing, this is the final limit. The material must stretch until it reaches this point. If the drawing depth exceeds the material’s fracture limit, the part will split.

Engineers must calculate the maximum drawing depth based on the fracture strength. This calculation accounts for the reduction in thickness. As the metal stretches, it gets thinner. This thinning reduces the cross-sectional area and lowers the fracture strength.

Do not assume the initial sheet strength applies to the bottom of the draw. The bottom of the part is the thinnest area. It has the least material to resist tearing. A safe design keeps the final thickness above a critical minimum. This margin prevents fracture at the most vulnerable point of the part.

In a practical scenario, imagine drawing a 50% depth cup from a 1 mm sheet. The bottom thickness will reduce significantly. If the material fractures at a thickness below 0.8 mm, the cup will split. The engineer must ensure the final thickness is above 0.8 mm. If the calculation shows the final thickness is 0.75 mm, the design is unsafe. The engineer must either reduce the drawing depth or increase the initial sheet thickness.

Fracture strength is also affected by temperature. Cold-drawn materials are stronger but less ductile. Warm-drawn materials are weaker but more ductile. If the material is cold, the fracture limit is lower. If the material is warm, the fracture limit is higher. The engineer must consider the temperature of the material at the time of drawing. This information is often found in the material data sheet.

The fracture limit is the final check in the design process. It ensures the part will not break during production. If the fracture limit is exceeded, the part will split at the bottom. This is a catastrophic failure. It requires rework or scrap. The engineer must calculate the fracture limit carefully and apply a safety margin.

4. Analyzing Texture and Grain Direction

Sheet metal is not uniform. It has a texture developed during rolling. This texture influences how the metal flows in the die. The grain direction is the direction of the metal’s internal structure.

If the grain direction is aligned with the drawing direction, the metal flows more easily. If it is cross-aligned, the metal may resist flow and cause wrinkles. This is a common cause of uneven drawing.

Check the texture on the material certificate. Some suppliers provide the grain direction. If it is not specified, assume the worst case. Design the die to handle the most difficult flow scenario. This may require adding extra drawing stations or adjusting the die profile to guide the metal properly.

Grain direction is critical for deep-drawn parts with complex shapes. Consider a deep-drawn housing with multiple flanges. If the grain direction is not aligned with the draw, the metal will resist flow in certain directions. This causes wrinkles in the flanges. The engineer must design the die to guide the metal along the grain direction. This may require adding draw beads or adjusting the die profile.

For simple cup parts, grain direction is less critical. The metal flows in a circular pattern. The grain direction has less effect on the outcome. For complex parts, grain direction is a major factor. The engineer must check the grain direction on the material certificate. If it is not specified, the engineer must assume the worst case.

The grain direction also affects the surface finish. If the grain is aligned with the draw, the surface finish is smoother. If it is cross-aligned, the surface finish may be rougher. This is a quality issue. The engineer must consider the surface finish requirements when selecting the material.

5. Verifying Material Testing and Certification

You cannot rely on the supplier’s word alone. Material testing is required to confirm that the sheet meets the specified grade. Every lot should have a mill certificate. This document lists the actual properties of the material.

Review the certificate for the specific lot number. The properties listed should match the spec you requested. If there is a discrepancy, reject the material. Do not use it for production parts.

Common tests include tensile testing and hardness testing. Tensile testing measures yield, fracture, and elongation. Hardness testing gives a quick check on the material’s resistance to deformation. Both tests are standard. If the lot fails these tests, the material is out of spec.

The mill certificate is a legal document. It states the chemical composition and mechanical properties of the material. If the properties do not match the spec, the supplier is responsible. The engineer must review the certificate carefully. Any discrepancy must be resolved before the material is used.

Tensile testing is the most comprehensive test. It measures yield strength, fracture strength, and elongation. It also provides the stress-strain curve. This curve is useful for understanding the material’s behavior during the draw. The engineer should request the stress-strain curve from the supplier. It helps in calculating the draw depth and the press tonnage.

Hardness testing is a quick check. It measures the material’s resistance to deformation. It is useful for verifying the material’s condition. If the hardness is too high, the material is too stiff. If it is too low, the material is too soft. The engineer must check the hardness on the mill certificate. If it is out of spec, the material must be rejected.

6. Identifying Red Flags in Material Selection

Some properties are warning signs. If you see these, stop and re-evaluate the material choice.

  • Low Elongation: This is the biggest red flag. If elongation is below the minimum required for the draw depth, the part will crack.
  • High Yield Strength: This may indicate a material that is too stiff. It will require more press tonnage and may not hold shape well.
  • Inconsistent Grain Direction: If the grain is not aligned, expect wrinkles. This is a design issue, not just a material issue.
  • Missing Certification: Never use material without a mill certificate. It is a compliance risk and a quality risk.

If any of these flags are raised, contact the supplier. Request a second lot or a different grade. Do not proceed with the design until the material is verified.

A red flag in material selection can lead to production stoppage. If the material is rejected during production, the press must be stopped. The die must be cleaned. The material must be replaced. This causes downtime and cost. The engineer must identify red flags early in the design process.

Low elongation is the most common red flag. It leads to cracking at the bottom of the draw. The part is scrapped. The engineer must check the elongation on the material certificate. If it is low, the engineer must switch to a different grade or reduce the draw depth.

High yield strength is another red flag. It leads to press overload. The press may not complete the stroke. The part is incomplete. The engineer must check the yield strength on the material certificate. If it is high, the engineer must switch to a different grade or use a larger press.

7. Creating a Final Feasibility Checklist

Use this checklist to validate the material before releasing the part for tooling.

  1. Confirm the Grade: Does the material match the drawing spec?
  2. Check Elongation: Is the elongation high enough for the drawing depth?
  3. Verify Yield Strength: Does the yield strength match the press capability?
  4. Calculate Fracture Limit: Is the drawing depth within the fracture limit?
  5. Review Texture: Is the grain direction favorable for the die design?
  6. Review Certification: Is the mill certificate complete and consistent?
  7. Test a Sample: Run a test draw on a small piece of the material.

This process ensures that the material is suitable for deep drawing. It reduces the risk of defects and rework. It is a simple step that saves significant time and cost in the long run.

The checklist is a final check. It ensures that all material properties are within the required range. It also ensures that the material is certified. The engineer must review the checklist before releasing the part for tooling.

Confirming the grade is the first step. The material must match the drawing spec. If it does not, the engineer must switch to a different grade.

Checking elongation is the second step. The elongation must be high enough for the drawing depth. If it is not, the engineer must reduce the draw depth or switch to a different grade.

Verifying yield strength is the third step. The yield strength must match the press capability. If it does not, the engineer must use a larger press or switch to a different grade.

Calculating the fracture limit is the fourth step. The drawing depth must be within the fracture limit. If it is not, the engineer must reduce the draw depth or increase the sheet thickness.

Reviewing texture is the fifth step. The grain direction must be favorable for the die design. If it is not, the engineer must adjust the die profile or switch to a different material orientation.

Reviewing certification is the sixth step. The mill certificate must be complete and consistent. If it is not, the engineer must reject the material.

Testing a sample is the final step. A test draw on a small piece of the material confirms the die design and the material behavior. It catches problems before production.

8. Practical Example: Selecting Steel for a Cup

Consider a simple cup part made from mild steel. The drawing depth is 50% of the diameter. The material has a yield strength of 250 MPa and an elongation of 20%.

First, check the elongation. 20% is a good value for this depth. The material should stretch without tearing.

Next, check the yield strength. 250 MPa is moderate. It should not require excessive press tonnage. The part should hold its shape well.

Finally, check the fracture limit. With a 50% draw, the thickness will reduce significantly. Ensure the final thickness is above the critical minimum. This is a standard check for any cup part.

If all these properties are within range, the material is feasible. If not, adjust the design or choose a different material. This is how engineers validate deep drawing properties in practice.

In this example, the mild steel is a good choice for the cup. The elongation is high enough for the 50% draw depth. The yield strength is moderate. It does not require excessive press tonnage. The fracture limit is within range. The material is feasible.

If the elongation was 10%, the material would not be feasible. The part would crack at the bottom. The engineer would need to switch to a different grade with higher elongation.

If the yield strength was 400 MPa, the material would require more press tonnage. The engineer would need to use a larger press or switch to a lower strength grade.

If the fracture limit was exceeded, the part would split. The engineer would need to reduce the draw depth or increase the sheet thickness.

9. Common Mistakes to Avoid

  • Ignoring Thickness Variation: Sheet metal has a thickness tolerance. A thicker sheet is stronger but harder to draw. A thinner sheet is easier to draw but weaker. Use the nominal thickness for calculations, but test with the actual thickness.
  • Assuming Uniform Properties: Properties can vary across the sheet. Edge areas may be different from the center. Use material from the center of the sheet for critical parts.
  • Skipping Test Draws: Even with good data, a test draw is necessary. It confirms the die design and the material behavior. Do not skip this step.

By following this checklist, you can ensure that the material is suitable for deep drawing. It is a structured approach that reduces risk and improves quality.

Ignoring thickness variation is a common mistake. Sheet metal has a thickness tolerance. A thicker sheet is stronger but harder to draw. A thinner sheet is easier to draw but weaker. The engineer must use the nominal thickness for calculations. But the engineer must test with the actual thickness. If the actual thickness is outside the tolerance, the engineer must reject the material.

Assuming uniform properties is another mistake. Properties can vary across the sheet. Edge areas may be different from the center. The engineer must use material from the center of the sheet for critical parts. The center of the sheet has the most uniform properties.

Skipping test draws is the most dangerous mistake. Even with good data, a test draw is necessary. It confirms the die design and the material behavior. It catches problems before production. The engineer must run a test draw on a small piece of the material. If the test draw fails, the engineer must adjust the die design or switch to a different material.

Frequently asked questions

What is the best material for deep drawing?

There is no single best material. It depends on the part geometry, drawing depth, and required properties. Mild steel and aluminum are common choices, but each has its own strengths and limits.

How do I know if a material is too stiff for drawing?

Check the yield strength. If it is too high, the material will require excessive force to deform. This can cause the press to overload or the die to wear quickly. Reduce the yield strength if possible.

What is the difference between yield strength and fracture strength?

Yield strength is the point where the material begins to deform permanently. Fracture strength is the point where it breaks. In drawing, you want a low yield strength and a high fracture strength to allow for deep drawing without tearing.

Do I need to test every lot of material?

Yes. Each lot should be tested or certified. Properties can vary between lots. Testing ensures that the material meets the spec and reduces the risk of defects.

Can I use a material with low elongation if I reduce the drawing depth?

Yes. If the elongation is low, you can reduce the drawing depth to keep the material within its limit. This is a common design change when a material is not ideal for deep drawing.